The devices must be positioned anywhere on the longitudinal axis of the arm, with the magnets that hook onto it and the body of the device that “looks towards the ground”, paying attention to the alignment with the axis of the arm itself. The arrow must be pointing as in the figure.
The device must be placed in a flat and stable place, so that the magnets are pointing towards the ground and the arrow points outwards. It is recommended to place it inside the quick coupler, if present, or on the forks connected to the piston, integral with the movement of the bucket.
Stirrup creation specifications: The support must be made in such a way that the angle it makes with respect to the ground is parallel to the segment that joins the end of the bucket with the bucket rotation joint.
Try pairing again on each tile. If it still doesn’t appear, we suggest turning off the sensors and turning them back on to carry out the process again.
Have you checked that:
Have you checked that:
Follow these steps:
1. Open the app and select ASSOCIATE COMPANY
2. Enter Device Name (a name to identify who the mobile phone belongs to) and the Company Code (you find the code on the Dashboard at the top left)
3. Close the app
4. Access the DEVICE item in the menu on the dashboard
5. You will find a request to associate it from the Device Name you entered, ACCEPT it
6. Under FLEET in the Create a new vehicle menu, enter the necessary information and the measurements of your vehicle
7. Open the APP again and check that your Company Code has appeared next to ASSOCIATE COMPANY. The association was successful!
8. Click on the list of vehicles, the list of loaded vehicles should appear.
Open the APP again and check that your Company Code has appeared next to ASSOCIATE COMPANY. The association was successful!
Once you have entered the FLEET menu item, select “NEW EXCAVATOR” or “NEW LOADER/MINI LOADER”.
Enter all the necessary info:
In the HOME, you can write a message to your operators (Device). To do this, you must enter the text of the question and the possible answers that the operator must provide.
On the OBJECTIVES section of the menu it is possible to monitor the progress of the objectives given to the operators. To create a new one, just select NEW in the top left, enter the text of the goal, start and end date and the operator to whom it is addressed. Then select SAVE. The operator will automatically receive the signal and can Accept or Reject it.
After entering the measurements of the vehicle, it is possible to use a special button to store the measurements, up to a maximum of 5 profiles (“Profile 1”, “Profile 2” etc…).
You can access future saved profiles in the “Vehicle List” section of the “Settings”.
On the Remote Dashboard, there is no limit to the number of profiles that can be stored.
Before starting, it is advisable to check on your mobile phone that Bluetooth and Geolocation (iOS or Android) are activated.
Link to activate Bluetooth iOS:
https://support.apple.com/it-it/HT204091
Link to activate Bluetooth Android:
https://support.google.com/android/answer/9075925?hl=en
Link to activate Geolocation iOS:
https://support.apple.com/it-it/HT207092
Link to activate Geolocation Android:
https://support.google.com/nexus/answer/3467281?hl=en
After entering the measurements of the vehicle or selecting it from the “Vehicle List”, follow these steps:
– Go to the “Measure” screen (lower left corner of the app).
– Only then turn on the devices, which will appear listed on the screen.
– On first installation, bind the devices to the corresponding arm by clicking on the box for each device. Associations must match the stickers on each body (iLink1 > Lift arm; iLink2 > Indenter arm; iLink3 > Bucket).
– Once the association has been made, click CONNECT.
It is used to define the ground floor on which the tracks of the vehicle are positioned. In the case of activity carried out on a horizontal plane, the more stable the positioning of the tracks on an equally horizontal plane, the more precise the measurement provided by the system.
It indicates the perpendicular distance that exists at this instant between the tip of the bucket and the horizontal plane defined during calibration. The measurement is given in meters.
The default distance indicates the projection on the horizontal plane of the distance between the tip of the bucket and the rotation pin of the lift arm. However, it is possible to provide a zero point to your liking (by placing the tip of the bucket on that point). By zeroing this point, the displayed distance will be positive by extending the arms of the vehicle, or vice versa negative by moving in the opposite direction.
If you need to change buckets, there is no need to change dimensions on the Remote Dashboard or on Vehicle Geometries; just click the Change Bucket icon and enter the new dimensions. In this way, the system will use the size entered on the gearbox for the current measurement only, without making a definitive change in the size of the vehicle.
The battery charge percentage is displayed on the main measurement screen at the top left.
The batteries are located inside the body.
It is not necessary to replace them as they contain a module that can be recharged through the USB cable and transformer supplied with the basic kit.
This feature is available for the iLink®Pro 3 Sensors setup only (with Bucket sensor). To use it:
AUTOMATIC: requires the fraction of the slope or its % gradient, the maximum height of the slope and then to position the tip of the bucket on the start point of the slope.
MANUAL: will require in two stages to position the tip of the bucket at the start and end point of the slope.
At the end of the setting phase, a screen will appear with the drawing of the slope and in real time the position of the bucket with respect to the profile.
The displayed value corresponds to the vertical distance between the bucket tip and the slope profile at that specific point.
